PIC18F45K20-I/MV【PDF 216/234 页】MCU 32KB FLASH 1536B RAM 40-UQFN

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3873

212页 213页 214页 215页 [216页]217页 218页 219页 220页

dsPIC33F

DS70165E-page 80

Preliminary

2007 Microchip Technology Inc.

4.4.1

PROGRAMMING ALGORITHM FOR

FLASH PROGRAM MEMORY

The user can program one row of program Flash

memory at a time. To do this, it is necessary to erase

the 8-row erase page that contains the desired row.

The general process is:

Read

eight

rows

program

memory

(512 instructions) and store in data RAM.

Update the program data in RAM with the

desired new data.

Erase the block (see Example 4-1):

Set the NVMOP bits (NVMCON<3:0>) to

‘0010’ to configure for block erase. Set the

ERASE (NVMCON<6>) and WREN (NVM-

CON<14>) bits.

Write the starting address of the page to be

erased into the TBLPAG and W registers.

Write 55h to NVMKEY.

Write AAh to NVMKEY.

Set the WR bit (NVMCON<15>). The erase

cycle begins and the CPU stalls for the dura-

tion of the erase cycle. When the erase is

done, the WR bit is cleared automatically.

Write the first 64 instructions from data RAM into

the program memory buffers (see Example 4-2).

Write the program block to Flash memory:

Set the NVMOP bits to ‘0001’ to configure

for row programming. Clear the ERASE bit

and set the WREN bit.

Write 55h to NVMKEY.

Write AAh to NVMKEY.

Set the WR bit. The programming cycle

begins and the CPU stalls for the duration of

the write cycle. When the write to Flash mem-

ory

done,

the

bit

cleared

automatically.

Repeat steps 4 and 5, using the next available

64 instructions from the block in data RAM by

incrementing the value in TBLPAG, until all

512 instructions are written back to Flash memory.

For protection against accidental operations, the write

initiate sequence for NVMKEY must be used to allow

any erase or program operation to proceed. After the

programming command has been executed, the user

must wait for the programming time until programming

is complete. The two instructions following the start of

the programming sequence should be NOPs, as shown

in Example 4-3.

EXAMPLE 4-1:

ERASING A PROGRAM MEMORY PAGE

; Set up NVMCON for block erase operation

MOV

#0x4042, W0

;

MOV

W0, NVMCON

; Initialize NVMCON

; Init pointer to row to be ERASED

MOV

#tblpage(PROG_ADDR), W0

;

MOV

W0, TBLPAG

; Initialize PM Page Boundary SFR

MOV

#tbloffset(PROG_ADDR), W0

; Initialize in-page EA[15:0] pointer

TBLWTL

W0, [W0]

; Set base address of erase block

DISI

; Block all interrupts with priority <7

; for next 5 instructions

MOV

#0x55, W0

MOV

W0, NVMKEY

; Write the 55 key

MOV

#0xAA, W1

;

MOV

W1, NVMKEY

; Write the AA key

BSET

NVMCON, #WR

; Start the erase sequence

NOP

; Insert two NOPs after the erase

NOP

; command is asserted

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式